STMicroelectronics MCP9701T Series, Digital Output Temperature & Humidity Sensor, Surface Mount, SMBus, ±2.5 %, 6-Pin

RS庫存編號:: 190-8476P
製造零件編號:: STTS751-1DP3F
製造商:: STMicroelectronics

STMicroelectronics MCP9701T Series, Digital Output Temperature & Humidity Sensor, Surface Mount, SMBus, ±2.5 %, 6-Pin

此圖片僅供參考，請參閲產品詳細資訊及規格

暫時無法供應

我們無法確定此產品何時有貨，RS 預計將其從我們的產品目錄中移除。

RS庫存編號:: 190-8476P
製造零件編號:: STTS751-1DP3F
製造商:: STMicroelectronics

產品概覽和技術數據資料表

法例與合規

產品詳細資訊

透過選取一個或多個屬性來查找類似產品。

選取全部	屬性	值
	品牌	STMicroelectronics
	Product Type	Temperature & Humidity Sensor
	Output Type	Digital
	Sub Type	Temperature Sensor
	Interface Type	SMBus
	Accuracy	±2.5 %
	Mount Type	Surface
	Pin Count	6
	Maximum Operating Temperature	125°C
	Minimum Operating Temperature	-40°C
	Minimum Supply Voltage	2.25V
	Maximum Supply Voltage	3.6V
	Package Type	UDFN
	Length	2.05mm
	Series	MCP9701T
	Standards/Approvals	No
	Width	2.05mm
	Height	500μm
	Automotive Standard	No

	選取全部
	品牌 STMicroelectronics
	Product Type Temperature & Humidity Sensor
	Output Type Digital
	Sub Type Temperature Sensor
	Interface Type SMBus
	Accuracy ±2.5 %
	Mount Type Surface
	Pin Count 6
	Maximum Operating Temperature 125°C
	Minimum Operating Temperature -40°C
	Minimum Supply Voltage 2.25V
	Maximum Supply Voltage 3.6V
	Package Type UDFN
	Length 2.05mm
	Series MCP9701T
	Standards/Approvals No
	Width 2.05mm
	Height 500μm
	Automotive Standard No

Datasheet

The STTS751 is a digital temperature sensor which communicates over a 2-wire SMBus 2.0 compatible bus. The temperature is measured with a user-configurable resolution between 9 and 12 bits. At 9 bits, the smallest step size is 0.5 °C, and at 12 bits, it is 0.0625 °C. At the default resolution (10 bits, 0.25 °C/LSB), the conversion time is nominally 21 milliseconds.

The open-drain EVENT output is used to indicate an alarm condition in which the measured temperature has exceeded the user-programmed high limit or fallen below the low limit. When the EVENT pin is asserted, the host can respond using the SMBus Alert Response Address (ARA) protocol to which the STTS751 will respond by sending its slave address.

The STTS751 is a 6-pin device that supports user-configurable slave addresses. Via the pull-up resistor on the Addr/Therm pin, one of four different slave addresses can be specified. Two order numbers (STTS751-0 and STTS751-1) provide two different sets of slave addresses bringing the total available to eight. Thus, up to eight devices can share the same 2-wire SMBus without ambiguity, thereby allowing monitoring of multiple temperature zones in an application.

The two-wire interface can support transfer rates up to 400 kHz.

STMicroelectronics MCP9701T Series, Digital Output Temperature & Humidity Sensor, Surface Mount, SMBus, ±2.5 %, 6-Pin

相關連結

第一時間了解我們的最新產品和優惠