Digilent 410-308 Programming Module for use with FPGA Devices
- RS庫存編號:
- 134-6473
- 製造零件編號:
- 410-308
- 製造商:
- Digilent
可享批量折扣
小計（1 件）*
TWD1,413.00
(不含稅)
TWD1,483.65
(含稅)
訂單超過 $1,300.00 免費送貨
暫時缺貨
- 從 2026年2月05日 發貨
**需要更多嗎？**輸入您需要的數量，然後按一下「查看送貨日期」以查詢更多庫存和送貨詳細資訊。
單位 | 每單位 |
|---|---|
| 1 - 4 | TWD1,413.00 |
| 5 + | TWD1,384.00 |
* 參考價格
- RS庫存編號:
- 134-6473
- 製造零件編號:
- 410-308
- 製造商:
- Digilent
規格
產品概覽和技術數據資料表
法例與合規
產品詳細資訊
透過選取一個或多個屬性來查找類似產品。
選取全部 | 屬性 | 值 |
|---|---|---|
| 品牌 | Digilent | |
| Product Type | Development Kit Accessory | |
| Accessory Type | Programming Module | |
| For Use With | FPGA Devices | |
| Standards/Approvals | No | |
| 選取全部 | ||
|---|---|---|
品牌 Digilent | ||
Product Type Development Kit Accessory | ||
Accessory Type Programming Module | ||
For Use With FPGA Devices | ||
Standards/Approvals No | ||
JTAG-SMT2 SMT Programming Module
The JTAG-SMT2 surface-mount programming module allows high-speed programming of Xilinx FPGA devices from a host PC. Users can solder the module directly onto a target board like any other component. Note: The JTAG-SMT2-NC part (RS 134-6473) does not have a USB connector fitted.
Features
• Compatible with all Xilinx tools
• Compatible with IEEE 1149.7-2009 Class T0 - Class T4 (includes 2-Wire JTAG)
• On-board ADP123AUJZ 300mA voltage regulator
• Separate Vref drives JTAG/SPI signal voltages
• Vref can be any voltage between +1.8V and +5V
• USB 2.0 HS port drives JTAG/SPI bus at up to 30Mbit/sec
• JTAG/SPI frequency settable by user
• PC connector: MicroUSB (JTAG-SMT2 only)
• GPIO pin allows processor reset of Xilinx Zynq platform
• SPI programming modes 0/2 up to 30Mbit/sec, modes 1/3 up to 2Mbit/sec
• Fully supported by Digilent's Adept software and Adept SDK
• Board dimensions: 22.75 x 21.5mm
RS Product Codes
• 134-6434 JTAG-SMT2 SMT Module
• 134-6473 JTAG-SMT2-NC SMT Module (without USB connector)
An FPGA is a semiconductor device consisting of a matrix of Configurable Logic Blocks (CLBs) connected through programmable interconnects. The user determines these interconnections by programming SRAM. A CLB can be simple (AND, OR gates, etc) or complex (a block of RAM). The FPGA allows changes to be made to a design even after the device is soldered into a PCB.
Note
This module is not needed for Digilent Xilinx FPGA boards as they have this functionality built-in.
相關連結
- Digilent 410-251 Programming Module for use with FPGA Devices
- Digilent Pcam 5C OV5640, PB200-358 Module for FPGA 410-358
- Digilent 410-249 Programming Adapter for use with Xilinx FPGAs
- Digilent 410-299 Programming Cable for use with Xilinx Tool, JTAG-HS3
- Digilent 410-372 Adapter for use with APSoC Development Board, FPGA
- Digilent Module 410-212
- Digilent Module 410-310
- Digilent 410-319-1 FPGA Development Board for Makers and Hobbyists Development Board